Search
Search U.S. government technical reports digitized or harvested by TRAIL.
Keyword Search
14045 results returnedSearch results
- A study of the torque equilibrium of an autogiro rotor
- Pressure distribution over an NACA 23012 airfoil with a slotted and a plain flap
- A study of air flow in an engine cylinder
- Wind-Tunnel Investigation of an NACA 23012 Airfoil with Various Arrangements of Slotted Flaps
- On some reciprocal relations in the theory of nonstationary flows
- The Aerodynamic Drag of Five Models of Side Floats N.A.C.A. Models 51-E, 51-F, 51-G, 51-H, 51-J
- N.A.C.A. Stall-Warning Indicator
- Noise From Propellers With Symmetrical Sections at Zero Blade Angle, 2
- Hydrodynamic and Aerodynamic Tests of Four Models of Outboard Floats: (N.A.C.A. Models 51-A, 51-B, 51-C, and 51-D)
- Tests of a Contra-Propeller for Aircraft
- Scavenging a Piston-Ported Two-Stroke Cylinder
- Discharge Characteristics of a Simulated Unit Injection System
- Flow observations with tufts and lampblack of the stalling of four typical airfoil sections in the NACA variable-density tunnel
- The Pressure Available for Ground Cooling in Front of the Cowling of Air-Cooled Airplane Engines
- A method of rapidly estimating the position of the laminar separation point
- A general tank test of a model of the hull of the Pem-1 flying boat including a special working chart for the determination of hull performance
- N.A.C.A. Stall-Warning Device
- An instrument for estimating tautness of doped fabrics on aircraft
- Resistance of transparent plastics to impact
- Tank tests to determine the effects of the chine flare of a flying-boat hull N.A.C.A. Model Series 62 and 69
- Stress concentration around an open circular hole in a plate subjected to bending normal to the plane of the plate
- Preliminary report on the characteristics of the NACA 4400R series airfoils
- Heat-transfer tests of a steel cylinder barrel with aluminum fins
- The drag of airplane radiators with special reference to air heating : comparison of theory and experiment
- The design of fins for air-cooled cylinders
- Activation of hydrocarbons and the octane number
- The effect of the slipstream on an airplane wing
- Free-spinning wind-tunnel tests of a low-wing monoplane with systematic changes in wings and tails IV: effect of center-of-gravity location
- Downwash and wake behind plain and flapped airfoils
- Design charts for predicting downwash angles and wake characteristics behind plain and flapped wings
- Airfoil section characteristics as affected by variations of the Reynolds number
- Aircraft rate-of-climb indicators
- The aerodynamic characteristics of six full-scale propellers having different airfoil sections
- Airfoil section data obtained in the NACA variable-density tunnel as affected by support interference and other corrections
- The effect of nacelle-propeller diameter ratio on body interference and on propeller and cooling characteristics
- Effect of fuel-air ratio, inlet temperature, and exhaust pressure on detonation
- Surface heat-transfer coefficients of finned cylinders
- The influence of directed air flow on combustion in spark-ignition engine
- Cooling on the front of an air-cooled engine cylinder in a conventional engine cowling
- Effects of elevator nose shape, gap, balance, and tabs on the aerodynamic characteristics of a horizontal tail surface
- The application of basic data on planing surfaces to the design of flying-boat hulls
- Airfoil Theory at Supersonic Speed
- Corrugated metal diaphragms for aircraft pressure-measuring instruments
- Pressure drop in tank and float vent tubes on diving airplanes
- An approximate spin design criterion for monoplanes
- Determination of the Profile Drag of an Airplane Wing in Flight at High Reynolds Numbers
- Local Instability of Centrally Loaded Columns of Channel Section and Z-Section
- Photoelastic Analysis of Three-Dimensional Stress Systems Using Scattered Light
- Pressure-Distribution Investigation of an N.A.C.A. 0009 Airfoil With a 50-Percent-Chord Plain Flap and Three Tabs
- Propeller Tests to Determine the Effect of Number of Blades at Two Typical Solidities