Browse TRAIL Inventories

Loss of xylidines in overwater storage of xylidine-blended fuel

Performance tests of NACA type A finned-tube exhaust heat exchanger

Oxygen boosting of an aircraft-engine cylinder in conjunction with internal coolants

A preliminary evaluation of the explosion jet-propulsion engine

Longitudinal characteristics and aileron effectiveness of a midwing airplane from high-speed wind tunnel tests

Measurement of free water in cloud under conditions of icing

Flame-visibility tests with individual exhaust stacks

Flight tests of the thermal ice-prevention equipment on the B-17F airplane

Flight tests of various tail modifications on the Brewster XSBA-1 airplane III : measurements of flying qualities with tail configuration 3

Flight tests of several exhaust-gas-to-air heat exchangers

Flight tests of a pursuit airplane fitted with an experimental bellows-type bob weight

Gasoline-water distribution coefficients of 27 aromatic amines

Note on the interpretation of wake-survey data and its use in the estimation of induced drag due to irregularities

Wind-Tunnel Procedure for Determination of Critical Stability and Control Characteristics of Airplanes

The effect of compression ratio, cooled exhaust gas mixed with inlet air, and inlet-air temperature on the knock-limited performance of a full-scale single-cylinder engine

The effect of continuous knock on the endurance of an aircraft engine cylinder

Effect of coaxial lapping of cast-iron piston rings on ring performance

Knock-limited performance of several internal coolants

Knock-limited performance of several internal coolants

Ditching tests with a 1/12-size model of the Army B-26 airplane in NACA tank number 2 and on an outdoor catapult

Determination of jet-boundary corrections to cowling-flap-outlet pressures by an electrical analogy method

The design of the optimum hull for a large long-range flying boat

Preignition-limited performance of several fuels

Knock-limited power outputs from a CFR engine using internal coolants 1: monomethylamine and dimethylamine

Effect of Mach number on position error as applied to a pitot-static tube located 0.55 chord ahead of an airplane wing

Airfoil section data from tests of 10 practical- construction sections of helicopter rotor blades submitted by the Sikorsky Aircraft Division, United Aircraft Corporation

Airfoil-contour modifications based on (epsilon)-curve method of calculating pressure distribution

Cascade investigation of buckets for a modern aircraft turbosupercharger

An analytical investigation of thermal-electric means of preventing ice formations on a propeller blade

Bending and shear stresses developed by the instantaneous arrest of the root of a moving cantilever beam

Compressibility and heating effects on pressure loss and cooling of a baffled cylinder barrel

Compressible potential flow with circulation about a circular cylinder

Analysis of factors affecting net lift increment attainable with trailing-edge split flaps on tailless airplanes

Analysis of a thermal ice-prevention system for wing leading-edge landing-light installations

Analysis of available data on the effectiveness of ailerons without exposed overhang balance

Effect of water injection on knock-limited performance of a V-type 12-cylinder liquid-cooled engine

Effect of tilt of the propeller axis on the longitudinal-stability characteristics of single-engine airplanes

Determination of the effect of wing flexibility on lateral maneuverability and a comparison of calculated rolling effectiveness with flight results

The determination of span load distribution at high speeds by use of high-speed wind-tunnel section data

Artificial aging of riveted joints made in alclad 24S-T sheet using A17S-T, 17S-T, and 24S-T rivets

Fatigue strength and related characteristics of aircraft joints 1: comparison of spot-weld and rivet patterns in 24S-T Alclad and 75S-T Aclad

The numerical solution of compressible fluid flow problems

The effect of internal pressure on the buckling stress of thin-walled circular cylinders under torsion

Guides for preventing buckling in axial fatigue tests of thin sheet-metal specimens

Analysis of square shear web above buckling load

The inward bulge type buckling of monocoque cylinders I : calculation of the effect upon the buckling stress of a compressive force, a nonlinear direct stress distribution, and a shear force

Performance tests of wire strain gages 1: calibration factors in tension

Nondestructive test methods for spot welds in aluminum alloys

Effect of curvature on strength of axially loaded sheet-stringer panels

Bibliography of piston ring lubrication


Published Year

Subject

Author

‹‹ previous 1 2 ... 19 20 21 22 23 24 25 ... 83 84 next ››